January 01, 2013
AODE, 4R70W/75W Valve Body Identification
Valve Body Xpress
4R70E, 4R70W, 4R75E, 4R75W
Heavy Duty Remanufactured Valve Body
Part No. F095HD
'01–'08. F095HD has solenoids that connect to a molded lead frame harness; includes 1-2 accumulator piston case springs.
Tech & Install Tips Find a DistributorSonnax heavy duty remanufactured valve body F095HD is built to overcome chronic shift and converter clutch apply complaints. It provides firmer shifts and a moderately increased pressure curve to improve performance, especially in truck and towing applications.
Numerous Sonnax valve upgrades are included to restore hydraulic clearances that lead to shift complaints, clutch distress, converter complaints and codes, solenoid issues and pressure problems. Line pressure rise has been moderately increased to overcome shift complaints, delayed engagements, and to increase holding power to the clutches.
A valve body stiffener plate at the 2-3 accumulator area is added to prevent leakage or damage at the separator plate that creates forward and direct clutch failure. High performance 1-2 accumulator springs are also included with the product to improve shift feel.
To guarantee the highest level of operational performance, this remanufactured valve body is tested on state-of-the art equipment to verify that solenoid feed, clutch, converter and line pressures match or exceed OE specifications.
- Sonnax components outperform & outlast OE to eliminate chronic shift & converter apply problems
- Firmer shifts under load & moderately increased line pressure improve transmission performance & durability
The valve body includes the following:
- OS PR & Boost Valve Assembly
- Elevated PR Spring
- BCC Plunger Valve Assembly
- OS Converter Limit Valve
- O-Ringed End Plugs
- New L/U and Dual-Shift Solenoids
- Performance 1-2 Accumulator Springs
- OS Solenoid Regulator Valve
- OD Servo Regulator Valve Assembly
- VB Retainer Plate
For '09-later applications, view F098HD.
AODE, 4R70W/75W Valve Body Identification
Part Number Chart
| Part Number | Description |
|---|---|
| [F091] | AODE, ’92 |
| F092 | AODE, ’93– ’95 |
| F093 (Warranty Only) | 4R70W, ’96– ’97, Soft Wire Harness |
| F094 | 4R70W, ’98–’00, Molded Lead Frame Harness |
| F095, F095HD | 4R70E/4R70W/75W/75E, ’01– ’08, Molded Lead Frame Harness |
| F098, F098HD | 4R70E/4R70W/75W/75E, ’09-Later, Soft Wire Harness |
’92-’00 Identification
Casting Number
- 1992 has 13mm dowel pins and an F2 Rough Forging Number.
- 1993-1995 have 13mm dowel pins and an F3 Rough Forging Number.
- 1996-2000 have 10mm dowel pins and an F6 Rough Forging Number.
- To identify if you have a ’96-’97 or a ’98-’00, use the solenoid identification. The ’96-’97 use a wired harness. The ’98-’00 uses a solid harness.
The Casting Number is located under the plate. See RED ARROW for location.
Solenoid Type Identification
| Molded Lead Frame Harness | Soft Wire Harness |
|---|---|
 |  |
4R70W, ’98-Later Identification
The valve body stiffener plate in the 2-3 accumulator area was eliminated on ’01-later Ford 4R70E, 4R70W, 4R75E and 4R75W transmissions. Sonnax adds a custom 2-3 accumulator support plate on these valve bodies. The addition of this plate eliminates separator plate cracking and cross-leaking.
| ’98–’00 F094 | ’01-Later F095, F095HD |
|---|---|
 |
|
| The ’98-’00 will have a hole inside the plate. See the arrow above. | ’01-Later will have a hole just to the rear of the small plate. See arrow above. |
